![configure router on a stick roas cisco configure router on a stick roas cisco](https://geek-university.com/wp-content/uploads/2015/10/configure_router_on_stick_switch.jpg)
Question 46: Which IOS command configures a switch for VTP client mode?.
![configure router on a stick roas cisco configure router on a stick roas cisco](https://cdn.networkacademy.io/sites/default/files/2020-11/inter-vlan-routing-example-1.png)
Question 45: In which two circumstances does a port security violation oc. Question 44: Which four LACP components are used to determine which hot-s. Question 43: The following commands have been issued on a Catalyst switch. Question 42: Which two configurations can you apply to a port so that it. Question 41: Which command prevents all access ports on a switch from sen. Question 40: What Cisco Catalyst switch feature can be used to define por. Question 39: Which security feature inspects ARP packets based on valid I. Question 38: After UDLD is implemented, a Network Administrator noticed t. Question 37: In the hardware address 0a, what does 07.ac repr.
Configure router on a stick roas cisco mac#
Question 36: Which two statements about dynamic MAC address learning are. Question 35: Which two commands or command sequences configure a switch s. Question 34: Which feature is automatically enabled when a voice VLAN is. Question 33: You have configured switches A and B in a network. Question 32: Which two statements about the local user database are true?. Question 30: Which command do you enter to enable Dynamic ARP Inspection. Question 29: You have recently deployed an access switch with two fiber c. Question 28: Which statement is true about Stackwise?. Question 27: What will be behavior of an access port when a tagged packet. Question 26: Which feature places a port in an err-disabled state when it. Question 25: The output displayed below is a result of what command? Inte. Question 24: Which two statements about VRRP are true? (Choose two.). Question 22: What happens if we add "line" on AAA command?. Question 21: Which two prerequisites for HSRP to become active on an inte. Question 20: If a network engineer applies the command mac-address-table. Question 19: Which command produced the following output? (Exhibit). Question 18: Which command enables you to determine whether any interface. Question 17: Which type of MAC address can be dropped by a switch that is. 3 comment Question 16: Which two commands display the VLANs that are present in the. Question 14: What command disables 802.1x authentication on a port and pe. Question 13: Inter-VLAN routing has been operating successfully for sever. Question 12: What Cisco switch feature allows IP phones to be automatical. Question 11: When executed on a HSRP group member named Router 10, what e.
![configure router on a stick roas cisco configure router on a stick roas cisco](https://images.surferseo.art/592f8e03-74fa-4674-9061-d617e11481c3.png)
Question 10: (Exhibit) Refer to the exhibit. Question 8: Instructions Enter IOS commands on the device to verify netw. Question 7: At which OSI layer does STP operate?.
Configure router on a stick roas cisco Pc#
Question 6: A network engineer is trying to deploy a PC on a network. Question 4: Which statement describes the result of issuing the spanning. Question 3: A company has the following network infrastructure. Question List (501q) Question 1: Which feature can you enable on your network to most effecti. Without this command, the encapsulation type and the VLAN ID remain Objective: Layer 2 Technologies Sub-Objective: Configure and verify trunking References: Home > Support > Configuring InterVLAN Routing > Configuring InterVLAN Routing on an External Cisco Router > Configuring IP InterVLAN Routing on an External Router Home > Support > Configuring InterVLAN Routing > InterVLAN Routing Configuration Examples > InterVLAN Routing with an External Cisco 7505 Router Example In the scenario, the subinterface created for VLAN 22 is not configured for inter-VLAN routing because the encapsulation command is missing. Consequently, this address will become the default gateway for each host in that VLAN. The first step sets up the switch: Configure the switch Configure the required VLANs Configure the switch port connecting to the router interface as a trunk port Enable dot1q or ISL encapsulation on the trunk port Configure the switch ports connecting to the VLANs as access ports Assign the access switch ports to respective VLANs The second step sets up the router: Configure the router Enable the router interface connected to the trunk switch port Create separate subinterfaces on the trunk router interface for each VLAN Enable dot1q or ISL encapsulation on the subinterfaces Assign IP addresses to each subinterface in the same subnet as the VLAN of which the interface will be a member. In a RoaS configuration, inter-VLAN routing is achieved in two steps. The given network diagram and the commands reflect a router-on-a-stick (RoaS) configuration. Explanation/Reference: Explanation: VLAN 22 is the only VLAN that does not participate in inter-VLAN routing through the rtrA router.